U.S. Army awards Worcester Polytechnic Institute $25 million to develop materials for cold spray additive manufacturing


The Worcester Polytechnic Institute (WPI), Massachusetts, has received a three-year, $25 million award from the U.S. Army Combat Capabilities Development Command Army Research Laboratory (CCDC-ARL) to develop metal cold spray additive manufacturing (CSAM) processes for the battlefield. 

In this project, WPI is tasked with characterizing and testing alloys which would ultimately enable the production and repair of military-grade components. This eliminates the extensive wait and high cost for manufacturing new parts for military units. 

“Cold spray is a foundational technology with a wide variety of applications, in the military and beyond,” said Danielle Cote, director of WPI’s Center for Materials Processing Data and the principal investigator for the ARL project.

ARL’s interest in Cold Spray Additive Manufacturing

CSAM deposits metal powders to near-supersonic speeds using pressurized gas. Without first melting the powders, the spray adheres to the metal upon contact due to the force of impact. The process can be reduced to a portable handheld applicator, which makes it attractive for use in the field. The technology has been previously used by engineers to repair engine gearboxes and make electric motors.

“If you’re on a mission and need to move quickly to a safer place, and a critical part on your vehicle breaks, you’re stuck unless you can repair it quickly. That’s where cold spray comes in,” added Cote. 

“The Army is interested in cold spray 3D printing as a repair technique [as] it’s cheaper to repair a part than to replace it, and you get the equipment back in service faster. The Army’s primary interest is unit readiness.”

Last month, ARL also awarded Rowan University, New Jersey $14.5 million to develop polymer CSAMAs part of the ARL project, the WPI research team will also work with several subcontractors, including the University of California Irvine, the University of Massachusetts Lowell and Penn State University.

Customizing CSAM metal powders

For most manufacturing methods such as casting and forging, metal alloys are altered by first being melted then heat treated. On the other hand, alloys are not melted before being cold sprayed, nor are they heat-treated after application. CSAM does not require alloys to be capable of melting for application. As a result, the research team can access a wider range of potential materials compared to other manufacturing methods.

To develop and study chemical and structural properties of the powders at nanoscale, WPI has acquired a variety of equipment as part of the ARL award. These include tools such as a SEM/EDS unit, a synchronous laser diffraction and dynamic image particle analyzer to determine powder morphologies, and nano indenters to measure nano-scaled mechanical properties.

The team has discovered that with the careful application of heat, the properties of cold spray powders can be fine-tuned and enhanced. Computational models are developed to determine the alloys chosen for study and thermal processing regimes adopted. Grounded in extensive laboratory experimentation and drawing on WPI’s voluminous databases of metal properties, the models make it possible and more effective to custom design powders for specific cold spray applications. 

WPI is developing metal powders like this for use in cold spray. Photo via WPI.

Improving military readiness by CSAM

WPI’s powder modification technique can manufacture engineering-grade alloys with high strength, toughness, and ductility. For example, the replacement of helicopter gearboxes often takes months or even years. Especially gearboxes require frequent maintenance, the cost for repairs and replacements is significant. On the other hand, CSAM can effectively repair or even manufacture parts of gearboxes, bringing helicopters back in the air quickly.  

Although ARL’s primary focus is on alloys for repairs, the award also allows WPI to explore CSAM applications beyond the battlefield such as applying antibacterial copper coatings on equipment. Furthermore, researchers in WPI’s robotics engineering program will explore the use of multi-axis robots to automate CSAM. 

“With the work we will be doing with powder development, in robotics, and in a number of other areas, I think we are going to go a long way with cold spray. There really are endless possibilities,” Cote concluded. 

Cote (left) is working with Kyle Tsaknopoulos, a postdoctoral fellow, on the research. Photo via WPI.

For more on additive manufacturing in academia, subscribe to our 3D Printing Industry Newsletter, follow us on Twitter, and like us on Facebook. Find talent for a project, or advance your career in 3D printing – join 3D Printing Jobs to apply and advertise.

Featured image shows WPI professor Danielle Cote (center) leading a WPI research team that will study cold spray 3D printing techniques. Photo via WPI.





Source link